Here are just a few of the alternative uses for your pliers: Using tongue and groove pliers like our new Klaw Pump Pliers you can easily remove a bathtub spout. Just stick one handle into the spout and turn the other handle counter-clockwise to remove it.
How do I make a plier?
Can I use a wrench instead of pliers?
Although pliers can be used to tighten and loosen nuts, this is a task better suited to the wrench. Pliers tend to damage the surfaces of fasteners and are usually more difficult to use than a properly-sized wrench.
What's the difference between a wrench and pliers?
Wrenches are designed to fit nuts, bolts and other standard fasteners. Pliers grip, turn, squeeze and rotate round or irregularly shaped objects of most any size, from baling wire to barbecue grills.
Related Question What can I use instead of pliers?
What do you do if you don't have a wrench?
Can you use pliers on a bolt?
Plumbers will often use tongue-and-groove pliers for just about everything. But a good rule of thumb is that for any fitting with a nut on it or a hex head, use a wrench. If you're going to use pliers on a hex-shaped fitting, bolt, or nut, at least use a pair that has a V-notch in the jaws to accommodate the hex shape.
What goes on the end of a ratchet?
A ratchet is a handle that snaps into one end of a socket by means of a square-drive connector. The other end of the socket fits over a fastener. A mechanism in the ratchet allows the handle to engage and tighten the fastener when you swing it in a clockwise direction and turn freely when you swing it counterclockwise.
What to do if you don't have a hammer?
Flat rock – Rocks with a completely flat edge are more suited to hammering nails into wood, putting furniture together, and driving a chisel. Long flat rock – This type of rock is perfect if you can't quite reach the thing you need to hammer.
Can pliers be used for tightening and loosening small nuts?
Pliers are often misused as general-purpose tools. Their use should be limited to operations for which they were designed: gripping and cutting (never for loosening or tightening nuts). Always use wrenches on nuts and bolt heads, never use a pliers. In fact, don't use pliers when any other tool will do.
What are tongue and groove pliers used for?
Tongue-and-groove pliers are commonly used for turning and holding nuts and bolts, gripping irregularly shaped objects, and clamping materials. It is also possible to rotate objects while keeping them in one position.
How do you hold a round pipe?
What is the most common type of pliers?
The needle nose pliers are among the most common type of pliers that feature on the toolboxes of many households. Just like its name implies, it has narrow jaws that are thinner towards the tip.
What are electrical pliers?
Electrical pliers are used when working with electricity and making electrical connections. Special cutters on the pliers allow them to be used to cut wire to length and to strip away the wire's outer coating as well. Typically, electrical pliers have rubber-coated handles to help protect the user from electric shock.
What are telephone pliers?
Telephone Work Pliers, Needle-Nose Side-Cutters, Type L1, 6-1/2-
How do you make a pin spanner wrench?
How do you tighten something without pliers?
Zip-tie. These wonderful little toolbox accessories aren't just used to tidy up cables and attach hubcaps, they can also be used in place of a spanner. Place the zip-tie around the nut as tightly as possible and using the tail of the zip-tie pull in the direction necessary to loosen or tighten the nut.
Why are they called pliers?
Lineman pliers are named for the occupation of electrical linesmen. The job of being an electrical linesman was born in the 1840s, with the invention of the telegraph. Linemen were those laborers who set the poles in place and strung the telegraph wires or lines between them.
What are nut jaw pliers used for?
Helping Hand. Acting as a handy, all‐purpose "backer wrench", these pliers can stand in when a second wrench of a given size is unavailable or fasteners are too damaged to turn with a wrench.
How do you release a strap?
How do you use sockets?
What are wrenches used for?
Wrenches are made in various shapes and sizes and are used for gripping, fastening, turning, tightening and loosening things like pipes, pipe fittings, nuts and bolts.
How do you make a homemade hammer?
How do you nail something without a hammer?
Is there an electric hammer?
The electric hammer is powered by an 18.5-volt, 3,000-mAh lithium-polymer battery, and is built from scratch mainly out of aluminum. Via a linkage, that rod subsequently thrusts the hammer's hinged head down and forward in an arc. Once the trigger is released, a spring pulls the rod/core back down again.
What tool that is designed to turn screws?
A screwdriver is a tool, manual or powered, used for driving screws. A typical simple screwdriver has a handle and a shaft, ending in a tip the user puts into the screw head before turning the handle.
Are used to turn screws nuts and bolts with hexagonal heads?
A hex key, Allen wrench or Allen key, is a simple tool used to drive bolts and screws with hexagonal sockets in their heads.
What type of tool is a screwdriver?
Screwdrivers are a type of hand tool used for the insertion and removal of screws. They are available in a multitude of variations to correspond to the correct screw drive. The drive or head of a screw has a shaped cavity and protrusion that fits the screwdriver tip.
What is a cutting plier?
: pliers that have a cutting blade on the side of the jaws.
How do you use pliers step by step?
What do you use locking pliers for?
Typically, locking pliers are used where more torque is needed to pry or remove objects or where added grip is needed for holding objects in place. Most uses includes loosening tight connection points such as pipe-joints, seized nuts and washers and removing broken nails.
What is a plumbing wrench?
A pipe wrench is an adjustable wrench that is used, as the name implies, on pipes. The top serrated jaw adjusts up and down to fit different size pipes. The unique feature of a pipe wrench is that the teeth will only grip when turning the wrench in one direction (see above), so it almost acts as a ratchet wrench.
Which material is used to join CI pipes?
Answer: Brazed Joint in Pipe Brazing is the process of jointing pipes using molten filler material at above 840oC. Brazing is generally used for joining copper pipes or copper alloy pipes.
What tool must be used if you want to hold pipe or round stock for cutting or treading of pipes?
Use a pipe wrench to turn or hold a pipe.
What's a needle nose?
: pliers with long slender jaws used for grasping small or thin objects.
What are reverse pliers called?
Sturdybilt Expanding Pliers solve different problems and are opposite of traditional pliers. Most pliers grab on the outside, but these pliers grab on the inside. The jaws open as you squeeze the handles together so they apply pressure on the inside of things.