Bank “1” is the side of the engine that contains cylinder 1. The oil control valve uses the motor oil in the engine as hydraulic fluid to facilitate this adjustment in cam position. When P0013 is thrown, it may leave the camshaft in question in a position that may be on the power side, the economy side, or anywhere in-between.

How much is a camshaft position sensor bank 1?

To have the sensor replaced, you can expect to pay between $130 and $200. For labor, you should pay between $70 and $90, and parts can cost as much as $100 or slightly more, but you could pay as little as $60 for them, depending on the kind of car you have.

What does intake camshaft position actuator open bank 1 mean?

Code P0010 stands for “A” Camshaft Position Actuator Circuit (Bank 1). The code indicates that your car's primary computer, which is also referred to as the powertrain control module (PCM), perceives a problem with one of the engine's VVT solenoids. That means it turns the solenoid on and off really fast.

What happens if you have a bad camshaft position sensor?

Car Will Not Start: Over time, as the camshaft position sensor fails, the signal it sends to the engine control module weakens. When the engine no longer receives the signal, you will not be able to start your car. Engine Misfires: A failing camshaft position sensor can cause your engine to misfire.

Related Question What is a camshaft bank 1?

Where is the camshaft position actuator circuit open bank 1?

The intake camshaft actuator features a gray electrical plug and is located closer to the front of the vehicle on the top of the cylinder head.

How much does it cost to replace a camshaft actuator?

The average for Camshaft Position Actuator is $665

Repair TypeZipCost
Camshaft Position Actuator96447$181
Camshaft Position Actuator64713$315
Camshaft Position Actuator36202$2848
Camshaft Position Actuator52804$500

How do I fix code p0345?

How much does a new camshaft cost?

Camshaft Replacement Cost - RepairPal Estimate. Labor costs are estimated between $850 and $1,072 while parts are priced at $459. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

What does intake a camshaft position Timing Over Advanced Bank 1?

The P0011 DTC stands for “A” Camshaft Position Timing Over Advanced or System Performance Bank 1. The code indicates that the ECM/PCM has been unable to correct a detected difference in the desired camshaft position angle and the actual camshaft position angle.

How do you clear a P0011 code?

  • Resetting the fault codes and performing a road test.
  • Changing the oil and filter to the proper oil viscosity for the engine specifications.
  • Repairing or replacing the wiring to the camshaft oil control valve for bank 1 intake camshaft.
  • Can I drive with a P0011 code?

    Can I drive my car with a P0011 code? but you will probably be all right. P0011 usually indicates a problem with the variable camshaft timing device. In most cases the car will run without trouble.

    Is P0010 serious?

    How Serious Is Code P0010? – Moderate. This trouble code will not prevent your vehicle from running. However, if left unsolved, this code could cause your vehicle to experience decreased power and fuel economy.

    What does the camshaft position actuator do?

    A camshaft actuator is a mechanical or electronic device that is mounted on the camshaft gear. Its purpose is to slightly advance or retard the timing of when the camshaft opens or closes the intake and/or exhaust valves.

    Is P0010 intake or exhaust?

    The P0010 code is set when the ECU detects a low voltage in the VVT circuit corresponding to the bank 1 intake cam.

    Can I drive my car with a p0013 code?

    A code p0013 stands for the variable camshaft timing solenoid voltage being out of range. The circuit may also have a short somewhere that is causing the rise or shortage of voltage. In the mean time, until further testing can be done, the vehicle should not be an issue to drive.

    Is bank 1 front or rear?

    Oxygen Sensor Identification Therefore, in an in-line 4-cylinder engine, the term “Bank 1, Sensor 1” simply refers to the front oxygen sensor. “Bank 1, Sensor 2” is the rear oxygen sensor. Typically, the engine bank that. contains cylinder 1 is called Bank 1.

    How To Clean Small Engine Carburetor
    Can A Bad Catalytic Converter Cause Car To Shut Off?