What are codes for transmission?
Full Transmission DTC Codes Table
|P0700||Transmission Control System (MIL Request)|
|P0701||Transmission Control System Range/Performance|
|P0702||Transmission Control System Electrical|
|P0703||Torque Converter/Brake Switch B Circuit|
How do I find my transmission code?
Open the driver's side door and find the white card on the side of the door that is filled with small black lettering. This card contains specific details about the year the car was made, its transmission, engine specifications and other details. Underneath or beside the “TR” symbol will be a number code.
What is a p700 code?
The OBD-II scanner error code P0700 problem is a generic code that applies to vehicles equipped with OBD-II. It refers to the transmission control module (TCM) in the automatic transmission. You may be seeing poor gas mileage or have transmission shifting problems. The engine could stall or run poorly.
Related Question What is the code for a bad transmission?
How do you diagnose a bad transmission solenoid?
What is code P0711?
P0711 code definition
The P0711 code is a generic powertrain code related to the transmission, including sensor failures and pressure faults. In this case, it means that the engine control module (ECM) or powertrain control module (PCM) has detected a fault or error with the Transmission Fluid temperature circuit.
What is code P0717?
P0717 is a diagnostic trouble code (DTC) for "Input/Turbine Speed Sensor No Signal". This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
What is a U0073 code mean?
Code U0073 stands for Control Module Communication Bus 'A' Off. The computers in modern vehicles (referred to as modules) communicate with one another over a data bus. This bus is called the controller area network (CAN).
What does CA mean on automatic transmission?
“CA” will appear in the gear display if a clutch abuse event is occurring. “AN” will appear in the gear display if the transmission goes into Auto Neutral.
What is code 88 on Eaton AutoShift?
Fault Code 88 – Inverter CAN Message Fault Detection
The following preconditions must be met before the system detects the fault: HCM ignition voltage is greater than 7 volts and less than 16 volts. HCM CAN data link fault is Inactive.
How does Eaton AutoShift work?
Using a three pedal system, the Solo self-adjusting clutch is used only for starting and stopping. Once the vehicle is in motion, AutoShift operates like an automatic transmission, with the efficiency of a manual transmission. This transmission is currently only available in Australia, Mexico, and South America.
What is P0720 code?
The P0720 code is a standard OBD-II trouble code that detects an issue with the output speed sensor circuit. The powertrain control module (PCM) relies on a signal from the output speed sensor, so that it can determine the correct shift strategy and send that information to the transmission.
How do I fix code po868?
Can being low on transmission fluid symptoms?
Symptoms of Low Transmission Fluid
What is code P0753?
A P0753 code indicates that the Powertrain Control Module (PCM) has detected an electrical abnormality in transmission shift solenoid A. Other associated codes include P0750, P0751, P0752, and P0754 trouble codes.
What does shift solenoid B do?
Shift solenoid B enables the transmission to shift from 2nd gear to 3rd gear. It does this by re-directing the flow of the transmission fluid which changes the position of the shift valves in the valve body.
What is a po700?
P0700 is set when the PCM detects a malfunction in the transmission control system. This malfunction causes the vehicle to set a Check Engine Light and trigger a failsafe mode. Once the failsafe mode is set it will remain until the fault is repaired or normal operation is detected.
What does C mean on code reader?
C = Catalyst. EV = Evaporative System. 2A = Secondary Air System. O = Oxygen Sensor Heater. E = Exhaust Gas Recirculation.